Project Easybox - Revision history

Joachim: /* Enter Easybox Administrator Mode */

2019-05-25T16:41:23Z

Enter Easybox Administrator Mode

@@ Line 1,378: / Line 1,378: @@
 Size: 8358608
 ...
 </nowiki>

Joachim: /* Enter Easybox Administrator Mode */

2019-05-25T15:29:31Z

Enter Easybox Administrator Mode

@@ Line 1,364: / Line 1,364: @@
 [screen is terminating]
 joachim@job2:~/brntool>
 </nowiki>

Joachim: /* Enter Easybox Administrator Mode */

2019-05-25T15:25:30Z

Enter Easybox Administrator Mode

← Older revision		Revision as of 15:25, 25 May 2019
Line 1,299:		Line 1,299:
	* exit terminal emulator (screen: [CTRL]+[A], [K], [y])		* exit terminal emulator (screen: [CTRL]+[A], [K], [y])

			This is what you should see now:
	~~git clone https~~:~~//github.com/rvalles/brntool~~
	~~cd brntool~~

	<nowiki>ROM VER: 1.0.3		<nowiki>ROM VER: 1.0.3
Line 1,364:		Line 1,362:

	[DANUBE Boot]:		[DANUBE Boot]:
			[screen is terminating]
			joachim@job2:~/brntool>
	</nowiki>		</nowiki>

Joachim: /* Enter Easybox Administrator Mode */

2019-05-25T15:24:00Z

Enter Easybox Administrator Mode

← Older revision		Revision as of 15:24, 25 May 2019
Line 1,302:		Line 1,302:
	git clone https://github.com/rvalles/brntool		git clone https://github.com/rvalles/brntool
	cd brntool		cd brntool

			<nowiki>ROM VER: 1.0.3
			CFG 01
			Read EEPROMX
			X



			=======================================================================
			Wireless ADSL Gateway DANUBE Loader V1.04.00 build Mar 19 2010 10:00:29
			Arcadyan Technology Corporation
			=======================================================================
			MXIC MX29LV640BB bottom boot 16-bit mode found

			Copying boot params.....DONE


			Press Space Bar 3 times to enter command mode ...123
			Yes, Enter command mode ...


			[DANUBE Boot]:

			======================
			[#] Set Serial Number
			[2] Use Normal Firmware
			[3] Use ART-Testing Firmware
			[9] Taggle ART Firmware Enable/Disable
			[A] Set MAC Address
			[E] Erase Flash
			[G] Run Runtime Code
			[H] Set Options
			[P] Print Boot Params
			[U] Upload to Flash
			[V] Set Board Version
			======================

			[DANUBE Boot]:!

			Enter Administrator Mode !

			======================
			[#] Set Serial Number
			[2] Use Normal Firmware
			[3] Use ART-Testing Firmware
			[9] Taggle ART Firmware Enable/Disable
			[A] Set MAC Address
			[E] Erase Flash
			[G] Run Runtime Code
			[H] Set Options
			[M] Upload to Memory
			[P] Print Boot Params
			[R] Read from Memory
			[T] Memory Test
			[U] Upload to Flash
			[V] Set Board Version
			[W] Write to Memory
			[Y] Go to Memory
			[Z] Dump DDR Ram Register
			======================

			[DANUBE Boot]:
			</nowiki>

Joachim at 15:20, 25 May 2019

2019-05-25T15:20:56Z

← Older revision		Revision as of 15:20, 25 May 2019
Line 1:		Line 1:
	= Easy Box to OpenWrt =		== Easy Box to OpenWrt ==

	== Hardware ~~Prep~~ ==		Roughly following https://openwrt.org/toh/astoria/arv752dpw22 (as of 2019-05-25)

			=== Hardware Preparation ===

	* USB2Serial adapter for 3.3V with 3 cables ending in female dupont		* USB2Serial adapter for 3.3V with 3 cables ending in female dupont
Line 7:		Line 9:
	* Something to open the box (prying tool, --screwdriver or similar)		* Something to open the box (prying tool, --screwdriver or similar)

	== Open the Box ==		==== Open the Box ====

	* unscrew the 2 x-Screws on the bottom		* unscrew the 2 x-Screws on the bottom
Line 14:		Line 16:
	* Put the mainboard out to see the serial connector in the center (4 pins, 1 (marked with a triangle) is 3.3V, then tx, rx and gnd.		* Put the mainboard out to see the serial connector in the center (4 pins, 1 (marked with a triangle) is 3.3V, then tx, rx and gnd.

	== Connect Serial ==		==== Connect Serial ====

	* First connect ground -> ground, then rx -> tx and tx -> rx		* First connect ground -> ground, then rx -> tx and tx -> rx
Line 25:		Line 27:
	If you see messages appearing now, all good. If not try swapping rx and tx connections and press restart button or repower		If you see messages appearing now, all good. If not try swapping rx and tx connections and press restart button or repower

	== My Boot Messages from the Original Box ==		==== My Boot Messages from the Original Box ====

	<nowiki>		<nowiki>
Line 1,279:		Line 1,281:
	ADSL> READY		ADSL> READY
	</nowiki>		</nowiki>

			=== Backup Original Firmware ===

			==== Get brntool ====

			git clone https://github.com/rvalles/brntool
			cd brntool

			==== Enter Easybox Administrator Mode ====

			replace /dev/ttyUSB2 with your com port device name (or use your other favorite terminal emulator)

			* run "screen /dev/ttyUSB2 115200"
			* power on the box
			* hurry press 3x space bar
			* type an exclamation mark (!) to enter the administration mode
			* exit terminal emulator (screen: [CTRL]+[A], [K], [y])


			git clone https://github.com/rvalles/brntool
			cd brntool

Joachim: /* My Boot Messages from the Original Box */

2019-05-25T15:07:15Z

My Boot Messages from the Original Box

← Older revision		Revision as of 15:07, 25 May 2019
Line 27:		Line 27:
	== My Boot Messages from the Original Box ==		== My Boot Messages from the Original Box ==

	<nowiki>		<nowiki>
	ROM VER: 1.0.3		ROM VER: 1.0.3
	CFG 01		CFG 01

Joachim: /* Connect Serial */

2019-05-25T15:04:27Z

Connect Serial

← Older revision		Revision as of 15:04, 25 May 2019
Line 19:		Line 19:
	* Plugin the adapter to a pc		* Plugin the adapter to a pc
	* On the pc start a terminal emulator (screen, putty, minicom, ...)		* On the pc start a terminal emulator (screen, putty, minicom, ...)
	* Configure the terminal emulator to use the new com port for the serial adapter (e.g. COM10 or /dev/ttyUSB2 or ...)		** Configure the terminal emulator to use the new com port for the serial adapter (e.g. COM10 or /dev/ttyUSB2 or ...)
	* Configure baud rate 115200		** Configure baud rate 115200
	* Plug in the power supply of the Easybox into its mainboard		* Plug in the power supply of the Easybox into its mainboard

Joachim: /* Open the Box */

2019-05-25T15:03:46Z

Open the Box

← Older revision		Revision as of 15:03, 25 May 2019
Line 12:		Line 12:
	* pry open the front cover. Needs much force, may break the plastic noses.		* pry open the front cover. Needs much force, may break the plastic noses.
	* Unscrew the 4 x-Screws on the mainboard edges		* Unscrew the 4 x-Screws on the mainboard edges
	* Put the mainboard out to see the serial connector (4 pins, 1 (marked with a triangle) is 3.3V, then tx, rx and gnd.		* Put the mainboard out to see the serial connector in the center (4 pins, 1 (marked with a triangle) is 3.3V, then tx, rx and gnd.

	== Connect Serial ==		== Connect Serial ==

Joachim: Created page with "= Easy Box to OpenWrt = == Hardware Prep == * USB2Serial adapter for 3.3V with 3 cables ending in female dupont * Small x-screwdriver * Something to open the box (prying t..."

2019-05-25T15:01:53Z

Created page with "= Easy Box to OpenWrt = == Hardware Prep == * USB2Serial adapter for 3.3V with 3 cables ending in female dupont * Small x-screwdriver * Something to open the box (prying t..."

Show changes