Update Marlin Firmware of Anycubic Kossel Pulley - Revision history

Joachim: /* My Diff in Configuration.h */

2023-08-28T10:49:05Z

My Diff in Configuration.h

← Older revision		Revision as of 10:49, 28 August 2023
Line 134:		Line 134:
	// (ms) Delay before the next move will start, to give the servo time to reach its target angle.		// (ms) Delay before the next move will start, to give the servo time to reach its target angle.
	// 300ms is a good value but you can try less delay.		// 300ms is a good value but you can try less delay.
			@@ -2558,7 +2558,7 @@
			// This option overrides the default number of encoder pulses needed to
			// produce one step. Should be increased for high-resolution encoders.
			//
			-#define ENCODER_PULSES_PER_STEP 3
			+#define ENCODER_PULSES_PER_STEP 4

			//
			// Use this option to override the number of step signals required to

	== Optional Diffs in Configuration_adv.h ==		== Optional Diffs in Configuration_adv.h ==

2023-08-27T16:01:23Z

Current Environment

← Older revision		Revision as of 16:01, 27 August 2023
Line 5:		Line 5:
	* First Run:		* First Run:
	** Erase EEPROM settings		** Erase EEPROM settings
	** Set Z-Probe: -16.0 (new hotend)		** Set Z-Probe: -15.6 (new hotend)
	** Config/Delta Kalib/Auto Kalib		** Config/Delta Kalib/Auto Kalib
	** Check: Manual (careful!) move to Z = 0, X=+-90, Y=+-90		** Check: Manual (careful!) move to Z = 0, X=+-90, Y=+-90

2023-08-27T15:58:42Z

Current Environment

← Older revision		Revision as of 15:58, 27 August 2023
Line 5:		Line 5:
	* First Run:		* First Run:
	** Erase EEPROM settings		** Erase EEPROM settings
	** Set Z-Probe: -15.8 (new hotend)		** Set Z-Probe: -16.0 (new hotend)
	** Config/Delta Kalib/Auto Kalib		** Config/Delta Kalib/Auto Kalib
	** Check: Manual (careful!) move to Z = 0, X=+-90, Y=+-90		** Check: Manual (careful!) move to Z = 0, X=+-90, Y=+-90
			*** since rod change only ok for XY +-70, outside head goes down!

	= Parameters =		= Parameters =

2023-08-27T15:54:59Z

Prepare

← Older revision		Revision as of 15:54, 27 August 2023
Line 28:		Line 28:
	git clone https://github.com/MarlinFirmware/Configurations.git marlin-config		git clone https://github.com/MarlinFirmware/Configurations.git marlin-config
	cd marlin-config		cd marlin-config
	git checkout 2.0.5.3		git checkout 2.1.2.1
	cd -		cd -
	git clone https://github.com/MarlinFirmware/Marlin.git marlin		git clone https://github.com/MarlinFirmware/Marlin.git marlin
	cd marlin		cd marlin
	git checkout 2.0.5.3		git checkout 2.1.2.1
	cd -		cd -

2023-08-27T15:54:17Z

My Diff in Configuration.h

← Older revision		Revision as of 15:54, 27 August 2023
Line 94:		Line 94:
	/**		/**
	* LCD Character Set		* LCD Character Set
			@@ -2623,7 +2623,7 @@
			// If you have a speaker that can produce tones, enable it here.
			// By default Marlin assumes you have a buzzer with a fixed frequency.
			//
			-#define SPEAKER
			+// #define SPEAKER

			//
			// The duration and frequency for the UI feedback sound.
	@@ -2354,14 +2354,14 @@		@@ -2354,14 +2354,14 @@
	* LED Type. Enable only one of the following two options.		* LED Type. Enable only one of the following two options.

2023-08-27T15:52:30Z

Edit in platformio.ini or avr.ini (since 2.1?)

@@ Line 124: / Line 124: @@
    // (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
    // 300ms is a good value but you can try less delay.
 == Edit in platformio.ini or avr.ini (since 2.1?) ==

2023-08-27T15:34:47Z

Edit in platformio.ini

← Older revision		Revision as of 15:34, 27 August 2023
Line 125:		Line 125:
	// 300ms is a good value but you can try less delay.		// 300ms is a good value but you can try less delay.

	== Edit in platformio.ini ==		== Edit in platformio.ini or avr.ini (since 2.1?) ==

	Since my notebook has more than one usb serial port, I needed to tell platformio which one connects to the printer:		Since my notebook has more than one usb serial port, I needed to tell platformio which one connects to the printer:

2023-08-27T15:33:13Z

Current Environment

← Older revision		Revision as of 15:33, 27 August 2023
Line 4:		Line 4:
	* Marlin 2.1.2.1, self compiled for RGBW- and Servo0 support		* Marlin 2.1.2.1, self compiled for RGBW- and Servo0 support
	* First Run:		* First Run:
	* Erase EEPROM settings		** Erase EEPROM settings
	* Set Z-Probe: -15.8 (new hotend)		** Set Z-Probe: -15.8 (new hotend)
	* Config/Delta Kalib/Auto Kalib		** Config/Delta Kalib/Auto Kalib
	* Check: Manual (careful!) move to Z = 0, X=+-90, Y=+-90		** Check: Manual (careful!) move to Z = 0, X=+-90, Y=+-90

	= Parameters =		= Parameters =

2023-08-27T15:32:56Z

Current Environment

← Older revision		Revision as of 15:32, 27 August 2023
Line 2:		Line 2:

	* TriGorilla Board, based on AtMega 2560		* TriGorilla Board, based on AtMega 2560
	* Marlin 1.1.9, ~~selfcompiled~~ for ~~RGB~~ support		* Marlin 2.1.2.1, self compiled for RGBW- and Servo0 support
			* First Run:
			* Erase EEPROM settings
			* Set Z-Probe: -15.8 (new hotend)
			* Config/Delta Kalib/Auto Kalib
			* Check: Manual (careful!) move to Z = 0, X=+-90, Y=+-90

	= Parameters =		= Parameters =

2020-06-27T10:08:44Z

Documentation

← Older revision		Revision as of 10:08, 27 June 2020
Line 16:		Line 16:
	* https://marlinfw.org/docs/basics/install_platformio_vscode.html		* https://marlinfw.org/docs/basics/install_platformio_vscode.html

	== Prepare ==		= Prepare =

	mkdir ~/git		mkdir ~/git
Line 30:		Line 30:
	cd -		cd -

	== ~~Configure~~ ==		= Configure =

			== Generic Anycubic Kossel ==

	cd ~/git/marlin/Marlin/		cd ~/git/marlin/Marlin/
Line 36:		Line 38:
	ln -sf ../../marlin-config/config/examples/delta/Anycubic/Kossel/Configuration_adv.h .		ln -sf ../../marlin-config/config/examples/delta/Anycubic/Kossel/Configuration_adv.h .

	=== Diff in Configuration.h ===		== My Diff in Configuration.h ==

	Identification, remote control, heatbed, z-probe, rgbw and sensor as used on my pulley		Identification, remote control, heatbed, z-probe, rgbw and sensor as used on my pulley